Skip to main content

Definition of Friction and Brake


Friction is main bad effect of a motor. Friction reduce a motor efficiency. Friction mainly create in a motor for it’s corrosion or speed ratio on spin. In a motor flywheel adjusted in drive wheel. In a gear ratio it mainly depends on gear and flywheel transfer energy on drive wheel. In a car or heavy load carrier vehicle used spring for reduce vibration and friction reduce generally use oil especially used in lubrication. For friction reduce one should firstly should select a metal which is help to reduce corrosion that’s means high resistance corrosion.
Brake is also more important issue for a vehicle for it speed is slow down. There are three types of  brake such as electromagnetic, disc and drum brake. Kinetic energy change to heat energy a vehicle speed reduce. Most of the car and vehicle use hydraulic brake which based in 6 steps and depends on 6 parts. These six parts are valve, road wheel, pedal, cylinder and boost. Electromagnetic brake is more popular for it’s more facilities such as easily control, use electrically clutch, only used in electricity and heat.

Image source:  smartcare.repairnet

Comments

Popular posts from this blog

Turbine

Turbine:

“Equalizer connection is needed in lap winding armature but not in wave winding “ why ?

The equivalent circuit of a four point – pole dynamo with a simplex winding. The voltage induced in each path is assumed to both to be same and should be if the reluctance of each magnetic path is the same, so that the lines of flux cut by each inductor of each path are the same. However wear of the bearings or deflection of the armature shaft may cause the armature to be closer to some poles and farther from others, thus changing the length of the air gap, and therefore the reluctance of the magnetic circuits of the poles is not identical. This factors cause the voltage in the materials making up the magnetic circuit. These factors cause the voltage in each parallel path differ, and the unequal voltages in turn cause flow of a circulatingcurrent through the windings and brushes , undue heating of the armature and waste the power. To reduce the circulating current, points on the winding which should be at the same potentials are brought to the same potentials by connecting them with …

What are the advantages and disadvantages of hydraulic brakes?

Boiler

Boiler


Boiler: A steam boiler is usually a closed vessel made of steel. Its function is to transfer the heat produced by the combustion of fuel to water and ultimately to generate steam.
Types of boiler:
           1. Fire tube or smoke tube boiler            2. Water tube boiler




                                          Figure: Boiler
Fire tube boiler: In fire tube steam boilers, the flames and hot gases, produced by the combustion of fuel pass through the tubes which are surrounded by water. Fire tube boilers are generally used for relatively small steam capacities and low to medium steam pressure. As a guideline fire tube boilers are completive for steam rates up to 12000kg/h and pressures up to 18 kg/cm².Fire tube boilers are available for operation with oil, gas or solid fuel.


                                   Figure: Vrious parts of boiler
Example: Cochran boiler, Locomotive boiler, Scotch marine boiler, Velcon boiler, simple vertical boiler.


Thermal Power Plant

Why a dc generator fails to build up voltage?

Differentiate among progressive die, compound die and combination die.

Progressive die: The dies which performed two or more operations at different stages every time the ram descends is known as Progressive die.
The principle advantage of Progressive die is in the number of operations that can be achieved with one handling of the stock strip. The main disadvantage is that work pieces may become “dished” as they pushed through the die as they generally have very little support.






Compound die: A compound die differs from a progressive die in that it performs two or more cutting operations during one stroke of the press at one station only.

Compound dies are slower in operation than progressive dies but they have advantages for certain jobs, especially where tolerance are close (1)the cutting operation, by the action of the knockout plate ,ensures flatness of the blank.2 Large parts can be blanked in a smaller press if compound dies rather than progressive dies areused.
Combination dies:A die in which a cutting operation is combined with a noncutting operation …

Power transmission of a shaper machine

What is basic difference between a Turbine and The Pump?

what is the difference between long shunt and short shunt dc generator?